The use of different blood sample preparations in the development of biomarkers for the environmental monitoring of domestic farm animals

The application of biological effect monitoring for the detection of environmental chemical exposure in domestic animals is still in its infancy. This study investigated blood sample preparations in vitro for their use in biological effect monitoring. When peripheral blood mononuclear cells (PBMCs), isolated following the collection of multiple blood samples from sheep in the field, were cryopreserved and subsequently cultured for 24 hours a reduction in cell viability (<80%) was attributed to delays in the processing following collection. Alternative blood sample preparations using rat and sheep blood demonstrated that 3 to 5 hour incubations can be undertaken without significant alterations in the viability of the lymphocytes; however, a substantial reduction in viability was observed after 24 hours in frozen blood. Detectable levels of early and late apoptosis as well as increased levels of ROS were detectable in frozen sheep blood samples. The addition of ascorbic acid partly reversed this effect and reduced the loss in cell viability. The response of the rat and sheep blood sample preparations to genotoxic compounds ex vivo showed that EMS caused comparable dose-dependent genotoxic effects in all sample preparations (fresh and frozen) as detected by the Comet assay. In contrast, the effects of CdCl2 were dependent on the duration of exposure as well as the sample preparation. The analysis of leukocyte subsets in frozen sheep blood showed no alterations in the percentages of T and B lymphocytes but led to a major decrease in the percentage of granulocytes compared to those in the fresh samples. The percentages of IFN-γ and IL-4 but not IL-6 positive cells were comparable between fresh and frozen sheep blood after 4 hour stimulation with phorbol 12-myrisate 13-acetate and ionomycin (PMA+I). These results show that frozen blood gives comparable responses to fresh blood samples in the toxicological and immune assays used.

Antenna development for wearable wireless sensing systems

Embedded wireless sensor network (WSN) systems have been developed and used in a wide variety of applications such as local automatic environmental monitoring; medical applications analysing aspects of fitness and health energy metering and management in the built environment as well as traffic pattern analysis and control applications. While the purpose and functions of embedded wireless sensor networks have a myriad of applications and possibilities in the future, a particular implementation of these ambient sensors is in the area of wearable electronics incorporated into body area networks and everyday garments. Some of these systems will incorporate inertial sensing devices and other physical and physiological sensors with a particular focus on the application areas of athlete performance monitoring and e-health. Some of the important physical requirements for wearable antennas are that they are light-weight, small and robust and should also use materials that are compatible with a standard manufacturing process such as flexible polyimide or fr4 material where low cost consumer market oriented products are being produced. The substrate material is required to be low loss and flexible and often necessitates the use of thin dielectric and metallization layers. This paper describes the development of such a wearable, flexible antenna system for ISM band wearable wireless sensor networks. The material selected for the development of the wearable system in question is DE104i characterized by a dielectric constant of 3.8 and a loss tangent of 0.02. The antenna feed line is a 50 Ohm microstrip topology suitable for use with standard, high-performance and low-cost SMA-type RF connector technologies, widely used for these types of applications. The desired centre frequency is aimed at the 2.4GHz ISM band to be compatible with IEEE 802.15.4 Zigbee communication protocols and the Bluetooth standard which operate in this band.

Development of miniaturized wireless sensor nodes suitable for building energy management and modelling

Buildings consume 40% of Ireland's total annual energy translating to 3.5 billion (2004). The EPBD directive (effective January 2003) places an onus on all member states to rate the energy performance of all buildings in excess of 50m2. Energy and environmental performance management systems for residential buildings do not exist and consist of an ad-hoc integration of wired building management systems and Monitoring & Targeting systems for non-residential buildings. These systems are unsophisticated and do not easily lend themselves to cost effective retrofit or integration with other enterprise management systems. It is commonly agreed that a 15-40% reduction of building energy consumption is achievable by efficiently operating buildings when compared with typical practice. Existing research has identified that the level of information available to Building Managers with existing Building Management Systems and Environmental Monitoring Systems (BMS/EMS) is insufficient to perform the required performance based building assessment. The cost of installing additional sensors and meters is extremely high, primarily due to the estimated cost of wiring and the needed labour. From this perspective wireless sensor technology provides the capability to provide reliable sensor data at the required temporal and spatial granularity associated with building energy management. In this paper, a wireless sensor network mote hardware design and implementation is presented for a building energy management application. Appropriate sensors were selected and interfaced with the developed system based on user requirements to meet both the building monitoring and metering requirements. Beside the sensing capability, actuation and interfacing to external meters/sensors are provided to perform different management control and data recording tasks associated with minimisation of energy consumption in the built environment and the development of appropriate Building information models(BIM)to enable the design and development of energy efficient spaces.